Search for:
Advanced Search
Home | Aluminum Fence | GTO Pro Gate Openers | Chain Link Fence | Wood Fence | Fence Tools | Access Control | Aluminum Railing
Shop by Category

Featured Product
Information
Products: 6058
Categories: 793
Prices: US Dollars
Currency
Language
Colonial 26 in Balusters - Black
Location: Shortcut to Homepage /Railing and Deck/Deckorators Balusters/Colonial Aluminum Balusters/Colonial 26 in Balusters - Black

Colonial 26 in Balusters - Black

Product Information
Colonial 26 in Balusters - Black

Deckorators® Colonial Balusters combine the look of our Classic baluster with a design detail that recalls traditional Colonial times. The rich look provides a distinguished appearance not found when using 2 x 2 balusters. Available in three colors, the Colonial is a 26” baluster for a 36” rail height.

Customize your deck or porch by alternating Colonial balusters with Classic balusters, and add Designer connectors to complete this look. Colonial balusters install to wood or composite railings. Colonial balusters easily install to wood or composite railings using Deckorators' baluster connectors.

Kit contents:

  • 10 Aluminum Balusters

Installation Instructions:

Items needed:
  • Deckorators baluster connectors (sold separately)
  • Deckorators stair connectors
  • Deckorators rail connectors
  • drill
  • tape measure
  • clamps
  • safety glasses
  • Carpenter's pencil
  • White rubber mallet
  • Support blocks (can be cut from scrap rail material)

Prior to construction, check with your local regulatory agency for special code requirements in your area.  Common railing height is 36".  Structural support should come from either the continuation of deck support posts that extend up through the deck floor or from railing posts that are bolted to the inside of the rim or outer joist.

Step 1:

Meaure railing opening from post to post to determine the length of each baluster section.

Step 2:

Cut top and bottom rails (2x4's) to length and clamp together. Mark top and bottom rails 4 1/2" on center, starting from the center of the rail.

Step 3:

Using a drill screw on the Deckorators baluster connectors (sold separately) on each mark using the screws provided.  Apply silicone caulk on each connector to prevent baluster from turning or rattling after installation is complete.  The caulk should be on the outside of the connector, where the baluster will make contact with the connector's outer edge.
Note: Specific types of treated lumber are known to corrode aluminum.  Deckorators baluster connectors provide a barrier between the balusters and treated lumber to ensure long term performance.

Step 4:


Place the bottom rail between the rail posts, supported by a 1 1/2" block (2x4 scrap material works best.)  Secure rail to posts using Deckorators rail connectors (sold separately) and slide balusters over the bottom connectors.  Carefully place top rail over the balusters, making sure each baluster is seated properly on each connector.

Step 5:

Inspect finished railing for proper baluster spacing and secure top rail.  Add a cap rail for a more finished look.

Step 6:

For rail sections longer than 4', support blocks are recommended.  These can be made from leftover 2x4 material.  Properly position the support block and toe nail it to the bottom rail and deck board.

Step 7:

Stair rails and balusters can present an interesting challenge.  Deckorators angled stair rail connectors (sold separately) create a snug and accurate baluster fit for stair rails angled from30 to 35 degrees.  Cut top and bottom stair rails at the proper angle.  Lay top and bottom stair rails alongside the posts and mark.

Step 8:

Clamp the top and bottom rails together with the top 2x4 rail inverted. Position rails as shown and mark 5 1/2" on center, working from the center out to the ends of the rails.



Step 9:

Properly position the connectors on the rails.  The top and bottom connectors will be facing opposite directions.  Screw the connectors in place.  To properly set angled connectors, begin screwing vertically until the screw bites into the wood.  Reposition screw to the proper angle and tighten.  Do not overtighten which can move the connector off center.

Step 10:

Make sure connectors are properly aligned, apply silicone caulk to each stair connector and assemble the top and bottom rails with the balusters. Then attach the full rail section between the rail posts.

Be the first to review this product!

Price: $24.66


Product Code: DB53654
Quantity: Add to Basket